Agilent HP 8517B S-Parameter Test Set, 0.045 to 50 GHz, 2.4 mm
Several S-Parameter tests sets are available for the Agilent 8510C
network analyzer for broadband coaxial measurements from 45 MHz
to 50 GHz. The Agilent 8517B test set has an architecture that develops
a separate reference channel for each incident port. RF switching
is done with a built-in electronic switch. For active device measurements,
the test sets include the ability to apply dc bias (external) to
the test port center conductors. Also available are two 60 dB step
attenuators, which allow control of the port 1 and port 2 signal
levels. Option 007 high dynamic range configuration.
Features:
- 45 MHz to 50 GHz
- Separate reference channel for each incident port
- Built-in electronic switch
Specifications:
Frequency Range 0.045 to 50 GHz
Test Ports (port 1 or 2
Nominal Operating Power Level:
+2 to -29 dBm
Opt 007: +5 to -16 dBm
Connector Type: 2.4 mm, male
Impedance, DC Bias: 50 ohm nominal, 500 mA, 40 Vdc
maximum
Attenuation Range (incident signal):
0 to 60 dB, in 10 dB steps
RF Input Connector (rear panel)
Maximum Input Power: +16 dBm
Connector Type: 2.4 mm, female
Dynamic Range (for transmission measurements)
Frequency Range GHz
.045 0.84 20 40
to 0.84 to 20 to 40 to 50
Maximum Power (dBm)
Measured at Port 2: +17 +8 +3 -4
Opt 007: +17 +12 +5 -5
Reference Power (dBm)
at Port 1 (nominal): +2 -7 -17 -29
Opt 007: +5 +2 -5 -16
Minimum Power
Measured at Port 2: -75 -97 -91 -90
Opt 007: -70 -92 -89 -91
Receiver
Dynamic Range (dB): 92 105 94 86
Opt 007: 87 104 94 86
System
Dynamic Range (dB: 77 90 74 61
Opt 007: 75 94 84 75
Measurement Port Characteristics
Frequency Range GHz
.045 0.84 20 40
to 0.84 to 20 to 40 to 50
Residual (dB)
Directivity: 42 42 38 36
Source Match: 41 3833 31
Load Match: 42 42 38 36
Reflection Tracking: ±0.001 ±0.008 ±0.02 ±0.027
Transmission Tracking: ±0.014 ±0.045 ±0.110 ±0.137
Crosstalk: 99 110 91 80
Raw (typical) (dB) (Before calibration/error
correction)
Directivity: 20 20 20 20
Source Match: 20 12 10 10
Load Match: 20 12 10 10
Ordering Information:
Agilent HP 8517B S-Parameter Test Set, 0.045 to
50 GHz, 2.4 mm
| Agilent 8517B |
S-Parameter Test Set, 0.045 to 50 GHz, 2.4 mm |
| Opt 001 |
Add IF switching circuitry |
| Opt 002 |
Delete step attenuators & bias networks |
| Opt 004 |
High power test set configuration |
| Opt 007 |
High power/dynamic range configuration |
| Opt 1BN |
Mil Std 45662A Calibration Certification |
| Opt 1BP |
Mil Std 45662A Calibration w/ Test Data |
| Opt 908 |
Rack flange kit, front handles detached |
| Opt 910 |
Extra operating and service manual set |
| Opt 913 |
Rack flange kit, handles attached |
| Agilent 8517B |
Calibration / Standards Compliant Calibration Options |
|
MetricTest
Solutions
