Fluke ScopeMeter® 190C Series

Specifications

Oscilloscope Mode
Vertical Deflection	Bandwidth: Fluke 199C= 200 MHz Fluke 196C= 100 MHz Rise time: Fluke 199C= 1.7 ns Fluke 196C= 3.5 ns Bandwidth limiter: User selectable 10 kHz or 20 MHz Number of inputs: 2 plus external trigger. All isolated from each other and ground. Input coupling: AC, DC with ground level indicator Input sensitivity: 5 mV/div to 100 V/div Input voltage: See general specifications for maximum rating Vertical resolution: 8 bit Accuracy: ±(1.5% of reading + 0.04 x range/div) Input impedance: 1 MW ± 1% // 15 pF ± 2 pF
Horizontal	Maximum real-time sample rate: Fluke 199C= 2.5 GS/s Fluke 196C= 1 GS/s Number of digitizers: 2 Time base range: Fluke 199C and 196C= 5 ns/div to 5 s/div Maximum record length: 1,200 points per input 27,000 points per input in ScopeRecord™-roll mode (5 ms/div ... 2 min/div) Accuracy: ± (0.01% of reading + 1 pixel) Glitch capture: 50 nsec (5 µsec/div to 1 min/div) Faster time bases have higher sample rates than 20 MS/s
Display and acquisition	Display modes: Input A, input B, dual, average, persistence, reference, invert, replay Waveform Mathematics: A+B, A-B, A*B all with user selectable scaling of the result ; A versus B (XY-mode) Acquisition modes: Normal, auto, single shot, ScopeRecord™, roll, glitch capture
Trigger and delay	Source: Input A, input B, external trigger input. All input references isolated from each other and ground. Modes: Automatic Connect-and-View™, free run, single shot, edge, delay, video, video line, selectable pulse width Connect-and-View™: Advanced automatic triggering that recognizes signal patterns, automatically sets up and continuously adjusts triggering, time base and amplitude. Automatically displays stable waveforms of complex and dynamic signals like motor drive and control signals. Video triggering: NTSC, PAL, PAL+, SECAM. Includes field 1 and 2 and line select. Pulse width triggering: Pulse width qualified by time. Allows for triggering t, = t, ą t, where t is selectable in minimal steps of 0.01 div or 50 nsec. Time delay: 12 divisions pre-trigger view to 1,000 divisions trigger delay
Automatic capture of 100 screens	The instrument ALWAYS memorizes last 100 screens (no user interaction or setup required). When an anomaly occurs on screen, there’s 10 seconds to press HOLD and review it. If one sets up the instrument for triggering on glitches or intermittent anomalies the unit operates in “baby-sit” mode and will capture 100 events. Replay: Manual or continuous replay. Displays the captured 100 screens as a “live” animation. The contents can also be viewed by manually scrolling backwards and forwards “screen by screen”. Replay storage: Up to 2 sets of 100 screens can be saved for later recall and analysis.
Automatic scope measurements	VDC, VAC rms, VAC+DC, Vpeak max, Vpeak min, Vpeak to peak, frequency (Hz), rise time with markers, fall time with markers positive pulse width, negative pulse width, positive duty cycle, negative duty cycle, amp AC, amp DC, amp AC+DC, power factor, watts, VA, VA reactive, phase, temperature °C, temperature °F, dBV, dBm into 50 W and 600 W
Cursor Measurements	Source: Input A or B Dual horizontal lines: Voltage at cursor 1 and 2, voltage between cursors Dual vertical lines: Time between cursors, voltage between markers. Automatic rise time with markers at 10% and 90%, fall time with markers at 10% and 90% Single vertical line: Min-Max and Average voltage at cursor position
Zoom	Up to 8x horizontal zoom

Meter Mode
General	Via 4 mm banana inputs. Fully isolated from scope inputs and scope ground. The specified accuracy is valid over the temperature range 18 °C to 28 °C (15 °F to 82 °F). Add 10 % of specified accuracy for each degree °C below 18 °C or above 28 °C (15 °F to 82 °F).
Maximum resolution	5,000 counts
Voltmeter ranges	500 mV, 5 V, 50 V, 500 V, 1,000 V
Accuracy	VDC: ± (0.5 % + 5 counts) VAC true rms 15 Hz to 60 Hz: ± (1 % + 10 counts) 60 Hz to 1 kHz: ± (2.5 % + 15 counts) VAC+DC true rms DC to 60 Hz: ± (1 % + 10 counts) 60 Hz to 1 kHz: ± (2.5 % + 15 counts)
Ohms	Ranges: 500 W, 5 kW, 50 kW, 500 kW, 5 MW, 30 MW Accuracy: ± (0.6 % + 5 counts)
Other meter functions	Continuity: Beeper on < 30 W (± 10 W) Diode test: Up to 2.8 V Amps: Amp DC, Amp AC, Amp AC+DC using an optional current clamp or shunt. Scaling factors: 0.1 mV/Amp to 100 V/Amp Temperature (°C, °F): With optional accessories. Scale factors 1 mV/°C or 1 mV/°F Input impedance: 1 MW ± 1% // 10 pF ± 2 pF Advanced meter functions: Auto/manual ranging, relative measurements (Zero reference), TrendPlot recording

Recorder Mode
ScopeRecord-roll mode	Dual input waveform storage mode. Source and display: Input A, Input B, Dual Memory depth: 27,000 points per input. Each point consist of Min-Max pair. Min-Max values: Min-Max values are measured at high sample rate ensuring capture and display of glitches Sample Recording Settings: Set Time base range = 5 ms/div to 1 min/div: Recorded timespan: 6 sec to 24 hrs Glitch capture: 50 nsec Sample rate: 20 MS/s Resolution: 200 µsec to 2.4 sec Set Time base range = 2 min/div: Recorded timespan: 48 hrs Glitch capture: 250 nsec Sample rate: 4 MS/s Resolution: 4.8 sec Recording modes: Single sweep, continuous roll, start on external trigger Horizontal scale: Time from start, time of day Zoom: Up to 1000 x zoom Memory: Up to 2 dual input ScopeRecordings can be saved for later recall and analysis
TrendPlot™ Recording	Dual input electronic paperless chart recorder. Plots, displays and stores meter and scope measurements. Source and display: Input A, Input B and DMM input Memory depth: 18,000 points record. Per record point a minimum, maximum and average value, and a time and date stamp are stored. Ranges: 5 s/div to 30 min/div in normal view mode. 5 min/div to 48 hour/div in view-all mode (overview of total record) Recorded timespan: Up to 22 days with a resolution of 100 sec. Recording mode: Continuous roll Measurement speed: 5 measurements per second maximum Horizontal scale: Time from start, time of day Zoom: Up to 64 x zoom Memory: Up to 2 TrendPlot recordings can be saved for later recall and analysis
Cursor measurements - All Recorder Modes	Source: Input A, B or DMM input Dual vertical lines: Min-Max or Average voltage. Time between cursors. Single vertical line: Min-Max or Average voltage. Absolute date and time or time from start.

General Specifications
Case	Design: Rugged, shock proof with integrated protective holster Drip and dust proof: IP51 according to IEC529 Shock and vibration: Shock 30 g, Vibration 3 g according to MIL-T28800E, Type III, Class 3, Style B
Display	Bright LCD with CCFL backlight, 50/80 Cd/m2 without/with power adapter. Size: 115 x 86 mm (4.5 x 3.4 inches) Resolution: 320 x 240 pixels Contrast and brightness: User adjustable, temperature compensated
Memory Save and Recall	Scope memories: 10 memory locations that each can contain two waveforms plus corresponding setup. Plus 5 extra memory locations after web refistration. Recorder memories: 2 memory locations that each can contain 100 captured dual input scope screens, or a dual input ScopeRecord (27,900 Min-Max pairs per input), or a dual reading Trendplot (18,000 Min-Max pairs and avg.
Real-time Clock	Time and date stamp for ScopeRecord, 100 captured screens and Trendplots.
Power	Line power: Country specific line voltage adapter/battery charger included Battery power: Rechargeable NiMH (installed) Battery operating time: 4 hours Battery charging time: 4 hours Battery power saving functions: Auto power down with adjustable power down time. On screen battery power indicator
Mechanical data	Size: 256 x 169 x 64 mm (10.1 x 6.6 x 2.5 inches) Weight: 1.95 kg (4.3 lbs)
Safety	Compliance: EN61010-1 (1993) Pollution degree 2, UL 3111-1 (1994), CAN/CSA C22.2 No.1010.1 (1992), ANSI/ISA S82.01 (1994)
Input voltage ratings	Maximum probe voltage: 1,000 V CAT II, 600 V CAT III (Maximum voltage between 10:1 probe tip (VPS200) and reference lead) Floating voltage: 1,000 V CAT II, 600 V CAT III (Maximum voltage between earth ground and any terminal (signal input or shielding)) Independently isolated: 1,000 V CAT II, 600 V CAT III inputs (Maximum voltage between any terminal of one input or probe (VPS200) and any other terminal of another input or probe (VPS200)) Maximum voltage on BNC input directly (input A or B): 300 V CAT III Maximum voltage on meter input: 1,000 V CAT II, 600 V CAT III
Environmental	Operating temperature: 0 °C to +50 °C Storage temperature: -20 °C to +60 °C Humidity 10 °C to 30 °C: 95% RH non condensing 30 °C to 40 °C: 75% RH non condensing 40 °C to 50 °C: 45% RH non condensing Maximum operating altitude: 3,000 m (10,000 feet) Maximum storage altitude: 12 km (40,000 feet) Electro-Magnetic Compatibility: EN 61326-1 for emission and immunity
Optically isolated PC/Printer interface	To printer: Supports HP Laserjet®,Deskjet®,Epson FX/LQ® and postscript printers via optional PAC 91 To PC: Transfer instrument settings, screen images and waveform data, compatible with FlukeView®software for Windows® via optional PM9080.
Warranty	3 years