Tektronix TDS7000 Specs at Metrictest.com

Tektronix Print Catalog 2001 Correction - on page 67 the table states that the TDS7404 has a Hardware Bandwidth Limits of 250MHz or 20 MHz. The TDS7404 does not have a Hardware Bandwidth limit feature.

	TDS7054	TDS7104	TDS7254	TDS7404
Input Channels	4	4	4	4
Analog Bandwidth (-3 dB)	500 MHz	1 GHz	2.5 GHz	4 GHz
Calculated Risetime 10 mV/div - 1 V/div	800 ps	400 ps	160 ps, typical	100 ps
Hardware Bandwidth Limits	250 MHz or 20 MHz
Input Coupling	AC, DC, Gnd		DC, Gnd
Input Impedance	1 megaohm ±0.5% or 50 Ohm ±1%		50 Ohm ±2.5%
Input Sensitivity, 1 megaohm	1 mV/div to 10 V/div
Input Sensitivity, 50 Ohm	1 mV/div to 1 V/div		2 mV/div to 1 V/div
Vertical Resolution	8-Bits (>11-Bits w/averaging)
Max Input Voltage, 1 megaohm	±150 V CAT I Derate at 20 dB/decade to 9 V_RMS above 200 kHz
Max Input Voltage, 50 Ohm	5 V_RMS, with peaks less than ±30 Volts		Determined by TekConnect Accessory
DC Gain Accuracy	1.00%		±(2% + (2% * offset))
Offset Range	1 mV/div - 100 mV/div ±1 V 101 mV/div - 1 V/div ±10 V 1.01 V/div - 10 V/div ±100 V		2 mV - 50 mV/div ±0.5 V 50.5 mV - 99.5 mV ±0.25 V 100 mV - 500 mV ±5 V 505 mV - 1 V/div ±2.5 V
Channel-to-channel Isolation Any Two Channels at Equal Vertical Scale Settings	>100:1 at 100 MHz and >30:1 at the Rated Bandwidth		>100:1 at <2-5 GHz and >40:1 at 4 GHz

Timebase System

	TDS7054	TDS7104	TDS7254	TDS7404
Timebase Range	200 ps/div - 40 s/div		50 ps - 10 s/div
Timebase Delay Time Range	16 ns to 250 s
Channel to Channel Deskew Range	±25 ns
Delta Time Measurement Accuracy	±(0.30 sample interval) + (15 ppm * reading)		0.06/ sample rate + 2.5 ppm * reading RMS	0.06/ sample rate + 1.5 ppm * reading RMS
Trigger Jitter (RMS)	8 ps RMS (typical)		6 ps RMS (typical)	6 ps RMS (typical)
Long Term Sample Rate and Delay Time Accuracy	±15 ppm over >1 ms interval		±1.5 ppm over any >100 ms interval

Acquisition System

	TDS7054	TDS7104	TDS7254	TDS7404
Real-time Sample Rates
1 channel (max)	5 GS/s	10 GS/s	20 GS/s	20 GS/s
2 channels (max)	5 GS/s	5 GS/s	10 GS/s	10 GS/s
3-4 channels (max)	2.5 GS/s	2.5 GS/s	5 GS/s	5 GS/s
Equivalent Time Sample Rate (max)	250 GS/s	250 GS/s	250 GS/s	250 GS/s
Maximum record length per channel with standard memory	400 k (1 ch), 200 k (2 ch), 100 k (4 ch)
with Opt. 1M	2 M (1 ch), 1 M (2 ch), 500 k (4 ch)
with Opt. 2M	8 M (1 ch), 4 M (2 ch), 2 M (4 ch)
with Opt. 3M	16 M (1 ch), 8 M (2 ch), 4 M (4 ch)
with Opt. 4M			32 M (1 ch), 16 M (2 ch), 8 M (4 ch)

Maximum Duration at Highest Real-time Resolution (1 ch)

	TDS7054	TDS7104	TDS7254	TDS7404
Time Resolution (Single-shot)	200 ps (5 GS/s)	100 ps (10 GS/s)	50 ps (20 GS/s)	50 ps (20 GS/s)
Max Duration with Standard Memory	80 µs	40 µs	20 µs	20 µs
Max Duration with Opt. 1M	400 µs	200 µs	100 µs	100 µs
Max Duration with Opt. 2M	1.6 ms	800 µs	400 µs	400 µs
Max Duration with Opt. 3M	3.2 ms	1.6 ms	800 µs	800 µs
Max Duration with Opt. 4M			1.6 ms	1.6 ms

Acquisition Modes

Edge - Positive or negative slope on any channel or front panel auxiliary input. Coupling includes DC, AC, noise reject, HF reject and LF reject.

Glitch - Trigger on or reject glitches of positive, negative or either polarity. Minimum glitch width is 1.0 ns with 200 ps resolution.

Width - Trigger on width of positive or negative pulse either within or out of selectable time limits (1 ns to 1 s).

Runt - Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again. Optional time qualification.

Timeout - Trigger on an event which remains high, low or either, for a specified time period, selectable from 1 ns to 1 s with 200 ps resolution.

Transition - Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative or either.

Setup/Hold - Trigger on violations of both setup time and hold time between clock and data present on any two input channels.

Pattern - Trigger when pattern goes false or stays true for specified period of time. Pattern (AND, OR, NAND, NOR) specified for four input channels defined as HIGH, LOW or Don't Care.

State - Any logical pattern of channels (1, 2, 3) clocked by edge on channel 4. Trigger on rising or falling clock edge.

Waveform Measurements

Amplitude - Amplitude, High, Low, Maximum, Minimum, Peak to Peak, Mean, Cycle Mean, RMS, Cycle RMS, Positive Overshoot, Negative Overshoot.

Time - Rise time, Fall time, Positive Width, Negative Width, Positive Duty Cycle, Negative Duty Cycle, Period, Frequency, Delay.

Histogram-related - Waveform count, Hits in box, Peak hits, Median, Maximum, Minimum, Peak to Peak, Mean (µ), Standard Deviation (sigma), µ+1 (sigma), µ+2 (sigma), µ+3 (sigma).

Waveform Processing/Math

Algebraic Expressions - Define extensive algebraic expressions including waveforms, scalars and results of parametric measurements e.g. (Integral (Ch1-Mean(Ch1))*1.414.

Frequency Domain Functions - Spectral magnitude and phase, real and imaginary spectra.

Window Functions - Rectangular, Hamming, Hanning, Kaiser-Bessel, Blackman-Harris, Gaussian, Flattop2, Tek Exponential.

Display Characteristics

Waveform Styles - Vectors, Dots, Intensified Samples, Variable Persistence, Infinite Persistence.

Computer System and Peripherals

Input/Output Ports

Probe Compensator Output - Front panel BNC connector, requires Probe Cal-Deskew Fixture (included) for probe attachment. Amplitude 200 mV ±20% into a >50 Ohm load, frequency 1 kHz ±5%.

Analog Signal Output Amplitude - Front-panel BNC connector, provides a buffered version of the signal that is attached to the Channel 3 input when Ch 3 is selected as trigger source. 20 mV/div ±20% into a 1 megaohm load, 10 mV/div ±20% into a 50 Ohm load.

Analog Signal Output Bandwidth, Typical -
TDS7054, TDS7104: 100 MHz into a 50 Ohm load.
TDS7254, TDS7404: 1 GHz into a 50 Ohm load.

Auxiliary Output Levels - Front-panel BNC connector, provides a TTL-compatible, polarity switchable pulse when the oscilloscope triggers.

Audio Ports - Miniature phone jacks for stereo microphone input and stereo line output.

USB Port - Allows connection or disconnection of USB keyboard and/or mouse while oscilloscope power is on.

SVGA Video Port - DB-15 female connector; connect a second monitor to use dual-monitor display mode. Supports basic requirements of PC99 specifications.

Scope VGA Video Port - DB-15 female connector, 31.6 kHz sync, EIA RS-343A compliant, connect to show the oscilloscope display, including live waveforms on an external monitor or projector.

Power Source

Power - 100-240 V_RMS, ±10%, 50/60 Hz; 115 V_RMS ±10%, 400 Hz; CAT II, <300 W (450VA).

Physical Characteristics Benchtop Configuration

Dimensions	mm	in.
Height	277	10.9
Width	455	17.9
Depth	425	16.75
Weight	kg	lbs.
Net	18	39
Shipping	37	80

Physical Characteristics Rackmount Configuration

Dimensions	mm	in.
Height	277	10.5
Width	502	19.75
Depth	486	19.125
Weight	kg	lbs.
Net	19	41
Kit	5.6	12.25

Mechanical

Cooling - Required Clearance.

	in.	mm
Top	0 or >3	76
Bottom	0	0
Left side	3	76
Right side	3	76
Front	0	0
Rear	0	0

Environmental

Temperature

Operating - 0°C to +50°C, excluding floppy disk and CD-ROM drives; +10°C to +45°C, including floppy disk and CD-ROM drives.

Humidity

Operating - 20% to 80% relative humidity with a maximum wet bulb temperature of +29°C at or below +50°C, noncondensing. Upper limit derated to 25% relative humidity at +50°C.

Nonoperating - With no diskette in floppy disk drive. 5% to 90% relative humidity with a maximum wet bulb temperature of +29°C at or below +60°C, noncondensing. Upper limit derated to 20% relative humidity at +60°C.

Altitude

Random Vibration

Operating - 0.00015 G²/Hz from 5 to 350 Hz, -3 dB/octave from 350 to 500 Hz, 0.000105 G²/Hz at 500 Hz. Overall level of 0.27 G_RMS.

Nonoperating - 0.0175 G²/Hz from 5 to 100 Hz, -3 dB/octave from 100 to 200 Hz, 0.00875 G²/Hz from 200 to 350 Hz, -3 dB/octave from 350 to 500 Hz, 0.006132 G²/Hz at 500 Hz. Overall level of 2.28 G_RMS.

Tektronix TDS7000 Series Digital Phosphor Oscilloscopes

TDS7054

TDS7104

TDS7254

TDS7404