| |
TEK TR210 Huntron Tracker
Features
- Performs In-circuit Component Testing
- Dual Channels Offer Unique Ability to Compare Known Good Board and
UUT to Find Defects
- Built-in Pulse Generator Tests Gate Fired Devices such as SCRs,
TRIACs, Opto-couplers
- Tests In-circuit CMOS, MOS, PLCs, Other Semiconductors, Resistors,
Capacitors, Inductors, Coils
Applications
- Maintain Motor Controllers, Robotic Systems and Programmable Logic
Controls In-plant
- Debug Engineering Prototypes
- Discover Manufacturing Defects - Find Wrong Values, Mis-installed
Components
- Troubleshoot and Repair Circuit Boards Without Schematics
- Test Components and Boards Without Power - Ideal for Catastrophic
Failures
- Find Intermittent Component Failures
Now you can extend the power of your TDS 200 Series oscilloscope
with the Tektronix TR210 Huntron Tracker.*1 This remarkable
device simplifies the testing of components while giving you a unique
current-voltage analog signature on the TDS 200 oscilloscope screen. The
TR210 Huntron Tracker and TDS 200 oscilloscope provide you an excellent
combination for troubleshooting circuit boards in design, manufacturing
or maintenance applications. The Tektronix TR210 Huntron Tracker provides
advanced troubleshooting capabilities to simplify testing of most types
of active and passive electronic components. A built-in pulse generator
lets you troubleshoot gate-fired devices such as SCRs, TRIACs and opto-couplers.
By energizing the gate, you can test the component in an active mode.
Analog Signature Analysis
Since the TR210 is used while the power to the circuit-under-test
is turned off, you avoid an accidental short that could cause further
damage. It allows you to analyze the overall health of a solid-state component,
which makes it perfect for finding leakage or substrate damage that has
brought a circuit board or a complete system down prematurely. Because
it can compare suspect components to known-good equivalents, it's also
ideal for troubleshooting when documentation is missing or incomplete.
The TR210 works by applying a current-limited AC signal across two points
of a component. The current flow causes a vertical deflection of the TDS
200 oscilloscope display, while the voltage causes a horizontal deflection.
Together, they give you a unique current-voltage "analog signature"
that represents the overall health of the device-under-test. By analyzing
each signature, you can quickly tell if a component is good, bad or marginal.
Real-world Troubleshooting Challenges
The Tektronix TR210 is ideal for troubleshooting Programmable
Logic Controls (PLCs). In troubleshooting multi-channel input modules,
technicians frequently run into a damaged channel because the IC buffers,
opto-couplers and drivers have been over-stressed. Using the built-in
pulse generator, the TR210 quickly troubleshoots opto-couplers and other
gate-fired devices, or simply compare the analog signature of one channel
against another. You'll usually find problems where you see differences
in signatures.
Specifications
|
Range
|
Vs
(Vpk)
|
Zs
(Ohm)
|
Current
(mARMS)
|
Pmax
(mW)
|
Pdiode
(mW)
|
|
High
|
60
|
74 k
|
0.6
|
6
|
0.2
|
|
Medium 2
|
20
|
27 k
|
0.6
|
2
|
0.2
|
|
Medium 1
|
15
|
1.2 k
|
8.5
|
23
|
2
|
|
Low 2
|
10
|
54
|
132
|
232
|
33
|
|
Low *1
|
3
|
10 k
|
0.21
|
0.1
|
0.05
|
Test Frequencies - 50 or
60 Hz, 200 Hz, 2,000 Hz.
Functions - Range Selection:
Auto or Manual. High Range Lockout.
Compare-A-Trace - Adjustable
(0.5 Hz to 5 Hz).
Pulse Generator -
Level: 0 V to 5 V.
DC Mode: +DC or -DC.
Pulse Mode: +Pulse, -Pulse, or both; adjustable duty cycle.
Environmental, EMC, Safety
Temperature -
Operating: 0°C to +40°C.
Non-operating: -50°C to +60°C.
Humidity -
Operating: 0 to 70% (per IEC 1010-1).
Altitude -
Operating: Up to 2000 m (6,600 ft.).
Non-operating: Up to 15,000 m (50,000 ft.).
EMC - Directive 89/336/EC.
Safety Compliance - UL3111-1,
CSA1010.1, EN61010-1.
Power
Source Power -
Voltage Ranges: 100 VAC, 230 VAC.
Line Frequency: 50 or 60 Hz.
Power - 15 W maximum.
Physical Characteristics
|
Dimensions
|
cm
|
in.
|
|
Height
|
6.2
|
2.45
|
|
Width
|
29.1
|
11.45
|
|
Depth
|
25.9
|
10.2
|
|
Weight
|
kg
|
lb.
|
|
Net
|
2.1
|
4.6
|
Specs
Ordering Information
Includes: Instruction Manual, One
Set ATL25 Test Probes, Common Test Leads, Two Mini-clip Leads, U.S. Power
Cord.
TR210 Recommended Accessories
Black Ground Leads - Order 98-0043.*2
Blue Clip Leads - Order 98-0036.*2
Foot Switch - Order 98-0314.*2
18 in. Coaxial BNC Cable - Order 012-0076-00.
36 in. Coaxial BNC Cable - Order 012-1341-00.
42 in. Coaxial BNC Cable - Order 012-0057-01.
|
|
MetricTest
Solutions
